TABLE OF CONTENTS
FIRMWARE UPGRADE METHOD
The Linksys E1200
is a Wireless-N router with four (4)
Ethernet ports. You can also use the router to share resources such as computers, printers and files. Various security features, such as SPI Firewall, help protect your data and your privacy while you are online. To know more about the E1200, click here
To know how to set up this Linksys Wireless-N router for the first time using Linksys Connect software, click here
The default IP address is 192.168.1.1. The username and the password is “admin”.
If you want to learn how to change the wireless network name (SSID)
using Linksys Connect, click here
There are two (2) ways to reset the Wireless-N router to factory defaults.
• Hardware Reset – Press and hold the Reset button located at the bottom panel for about five (5) seconds then release.
• Software Reset – Access the web-based setup page, go to Administration tab > Factory Defaults sub-tab, click the Restore Factory Defaults button.
For detailed instructions on how to reset your router to its factory default settings, click here
The warranty period is dependent on the country of purchase. For more information about your device's warranty, click here
You can power OFF the router first, then power it back ON, or you can click the Reboot button when you access the web-based setup page under the Basic Setup tab.
is a feature that allows you to access and manage your Linksys router from a remote location. You need to be connected to the Internet to be able to do remote management. The Linksys E1200 supports this feature. If you want to learn more about remote management, click here
7. Does E1200 use the Linksys Smart Wi-Fi service?
No. The Linksys Smart Wi-Fi is a free service that comes only with Linksys Smart Wi-Fi Routers (E4200v2, EA2700, EA3500, EA4500, EA6100, EA6200, EA6300, EA6350, EA6400, EA6500, EA6700, EA6900, EA9200, and WRT1900AC).8. What web browsers and operating systems is the E1200 compatible with?
- Windows XP SP3
- Windows Vista SP1 or later
- Windows 7
- Windows 8
- Windows 10
Mac OS X®
- Leopard 10.5
- Snow Leopard 10.6
- Mavericks 10.9
- Yosemite 10.10
- Internet Explorer 7
- Safari® 4
- Firefox® 3 or higher
9. What is the purpose of my router's Ethernet ports and LED lights?
The Ethernet ports allow you to connect the router to computers on your wired network and other Ethernet network devices. The LEDs on the back panel serve two (2)
purposes. The LED stays lit when the Linksys Wi-Fi Router, E1200 is connected to a device through one (1)
of the Ethernet ports. It flashes to indicate network activity on a certain port.
The default SSID of the E1200 is LinksysXXXXX.
NOTE: You have to upgrade your firmware to have LinksysXXXXX as your default SSID. XXXXX is the last five (5) digits of the router’s serial number, which is found at the bottom of the router.
The E1200 supports the following wireless security options: WPA2/WPA Mixed Mode
, WPA2 Personal
, WPA Personal
, WPA2/WPA Enterprise Mixed Mode
, WPA2 Enterprise
, WPA Enterprise
, and RADIUS
. To learn how to set up wireless security on your device, click here
Yes. The E1200 supports VPN tunnels using IPSec, L2TP or PPTP protocols as pass-through.
Yes. E1200 supports SPI firewall.
For E1200 v2, the SPI firewall protection is available for IPv6 and IPv4. To learn more about this feature, click here
Web Filter will filter Java, ActiveX, Cookies, and Proxy applications in the network.
You can view the devices that are connected to your wireless network by going to the router’s web-based setup page. Under the Setup tab, click the DHCP Reservation button. A list of all the MAC addresses of the wireless devices currently connected to your wireless network will be displayed.
FIRMWARE UPGRADE METHOD
Access your router’s web-based setup page
. To learn how, click here
. If you are using a Mac® computer, click here
Go to Administration tab and select Firmware Upgrade.
Select the file to upgrade by using the Browse... button.
Click Start to Upgrade.
The Linksys E1200 has the following releases:
- Hardware version 1.0, Firmware version Ver.1.0.03 (Build 4)
- Hardware version 2.0, Firmware version Ver.2.0.05 (Build 2)
- Hardware version 2.2, Firmware version Ver.2.0.05 (Build 2)
NOTE: For more details about this product, visit the Linksys Support Site to browse for more firmware updates and other support information.
DynDNS.org and TZO.com.
The router supports six (6) connection types: Automatic Configuration - DHCP, Static IP, Point-to-Point Protocol over Ethernet (PPPoE), Point-to-Point Tunneling Protocol (PPTP), Telstra Cable, and L2TP.
No. The E1200 does not support AP Isolation.
Yes. The E1200 supports wireless QoS and Internet Access Priority QoS.
No. The E120 does not transmit log information to a log server.
Yes. Before upgrading the firmware of your E1200, write down all your customized settings. After upgrading its firmware, you will have to re-enter all of your configuration settings.
Some Internet Service Providers (ISP) require you to register the MAC address of the modem, router or Ethernet adapter of the computer in order to access the Internet. If you do not wish to re-register the MAC address currently registered with your ISP, you may assign the MAC address you have currently registered with your ISP to the router using the MAC Address Clone feature.
If you want to clone the MAC address of the computer that you are using to configure the router, then click the Clone My MAC Address button. The router will automatically detect your computer’s MAC address, so you do NOT have to call your ISP to change the registered MAC address to the router’s MAC address. It is recommended that the computer registered with the ISP is used to enable this feature on the router.
You may need to perform MAC Address Cloning
when you have Cable Internet
. To learn how to set up MAC Address Cloning
for your Cable Internet service, click here
The Diagnostics sub-tab on the router’s web-based setup page contains the ping and traceroute tools that can be used to check your network’s connectivity to the Internet.
allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. To know the difference between Port Forwarding and Port Triggering, click here
To learn how to set up Port Range Forwarding
on a Linksys Wireless-N router, click here
NOTE: You can add up to 10 application names for Port Range Forwarding. For Linksys E1200 v2, you can add up to 15 application names.
will forward port based on the incoming port specified. Check your software application to find out what is necessary to enter in these fields. You can set up to 10
port triggering entries. To learn how to configure Port Range Triggering
in your router’s web-based setup page, click here
Demilitarized Zone (DMZ) allows one (1) local user to be exposed to the Internet for use of a special-purpose service, such as Internet gaming and videoconferencing. DMZ hosting forwards all the ports at the same time to one (1) computer. However, Port Range Forwarding is more secure because it only opens the ports you want to forward, while DMZ hosting opens all the ports of one (1) computer, exposing the computer to the Internet.
It supports three (3) network modes - 802.11b, 802.11g, and 802.11n.
Wireless MAC Filter
prevents or allows connectivity to the wireless network with the use of the MAC address of the wireless device. To know more about it, click here
NOTE: You can add up to 50 MAC addresses in the MAC Address Filter list. For Linksys E1200 v2, you can add up to 32 MAC addresses.
Universal Plug and Play (UPnP) allows Windows to automatically configure the router for various Internet applications, such as gaming and video conferencing.
15. Does the E1200 have Guest Access and Parental Controls features in the web-based setup page?
Yes. To know how to set up the Guest Access
feature of the E1200 using the web-based setup page, click here
. To know how to set up the Parental Controls
feature of the E1200 using the web-based setup page, click here
The Linksys E1200 v2
access feature offers both Internet Access Policy
and Parental Controls
. To learn more about this feature, click here
The E1200 comes with Linksys Connect Software version 1.3. To learn how to set up your Linksys Wireless-N router for the first time using Linksys Connect, click here
Older versions of Linksys Connect
for Mac computers have compatibility issues with the latest release of Mac OS X® (10.7 Lion)
. Only Linksys Connect versions 1.4.11222 and above are compatible with the Lion operating system. For more information, click here
No, the Linksys E1200 version 1 doesn’t support IPv6. However, the E1200 version 2 supports IPv6.
To find out more what Linksys devices support IPv6, click here
You can connect your mobile wireless devices and gaming consoles to your network using the Linksys Connect software. For more instructions, click here
For instructions on how to connect an iPhone® to your wireless router, click here
Check if the DHCP server setting of the E1200 router is Enabled. If it is not, you need to input a Static IP address on your TV.
To check if the DHCP server setting of your router is enabled, you need to access the router’s web-based setup page. For instructions, click here
. Once you’ve accessed the web-based setup page, view the DHCP server setting under Setup > Basic Setup
To connect your LCD/LED/Internet TV to the E1200 router using an Ethernet cable, check first if the TV has a LAN port. If it has one, read the TV’s user manual for instructions on what type of Ethernet cable to use (Category 5, 6 or 7) then use it to connect the TV to any of the Ethernet ports on the router.
NOTE: Checking the TV specification on the type of Ethernet cable to use is necessary to ensure that it will work properly once connected to the router.
Access the Network > Wi-Fi Settings menu of your TV and browse the list of detected wireless networks.
Select the wireless network name (SSID) of your router, enter the correct wireless password (if applicable) and select connect.
There are two (2)
ways to verify your computer’s connection to the network. You can:
- Check your computer’s Internet connectivity by opening a web browser on your computer and accessing any website or
- Perform a ping test to check the connection to the router.
To learn how to check your computer’s connection to the Internet, click here
. To check connection to the router, click here
There are many possible reasons why you can’t connect to the Internet. To learn more about them and how to perform troubleshooting steps to resolve these issues, click here
3. How do I disable the Wi-Fi Protected Setup™ (WPS) feature of my E1200?
The Wi-Fi Protected Setup™ is Enabled by default. To disable this feature, follow the steps below:
Access your router’s web-based setup page. To learn how, click here. If you are using a Mac computer, click here.
Go to the Wireless tab and select Basic Wireless Settings.
Under WPS, select Disabled.
NOTE: Ensure that your router's firmware is updated to have the WPS disable option.
4. What are the common problems with the E1200?
To learn about the common problems with E1200, and what to do, click here
5. How do I troubleshoot intermittent wireless connection with the E1200?
If you are having difficulties connecting some or all devices wirelessly, learn how to resolve these by clicking here