text.skipToContent text.skipToNavigation

Frequently Asked Questions for WAG54GP2

1.     What is the System Information for WAG54GP2?

a.     DHCP - Indicates if DHCP is enabled.
b.     Current IP - Displays the current IP address assigned to the ATA device.
c.     Host Name - Displays the current IP address assigned to the ATA device.
d.     Domain - Displays the network domain name of the ATA device.
e.     Current Netmask - Displays the network mask assigned to the ATA device.
f.     Current Gateway - Displays the default router assigned to the ATA device.
g.     Primary DNS - Displays the primary DNS server assigned to the ATA device.
h.     Secondary DNS - Displays the secondary DNS server assigned to the ATA device.

2.     What are the internet connection types for WAG54GP2?

a.     DHCP - Enable or disable DHCP. The default is yes.
b.     Static IP - Static IP address of ATA device, which takes effect if DHCP is disabled. The default is 0.0.0.0.
c.     NetMask - The NetMask used by ATA device when DHCP is disabled. The default is 255.255.255.0.
d.     Gateway - The default gateway used by ATA device when DHCP is disabled. The default is 0.0.0.0.

3.     What are the optional network configurations for WAG54GP2?

a.     Host Name - The host name of the ATA device.
b.     Domain - The network domain of the ATA device.
c.     Primary DNS - DNS server used by ATA device in addition to DHCP supplied DNS servers if DHCP is enabled; when DHCP is disabled, this is the primary DNS server. The default is 0.0.0.0.
d.     Secondary DNS - Sets the secondary DNS server to take over if problems are discovered with the Primary DNS server. This is in addition to DHCP-supplied DNS servers if DHCP is enabled; when DHCP is disabled, this is the secondary DNS server. The default is 0.0.0.0.
e.     DNS Server Order - Specifies the method for selecting the DNS server. The options are Manual (enter the IP address of the DNS server manually; that is do not look at the DHCP-supplied DNS table), Manual/DHCP, and DHCP/Manual.
f.     DNS Query Mode - Do parallel or sequential DNS Query. With parallel DNS query mode, the ATA device sends the same request to all the DNS servers at the same time when doing a DNS lookup, the first incoming reply is accepted by the ATA device. The default is parallel.
g.     Syslog Server - Specify the syslog server name and port. This feature specifies the server for logging ATA device system information and critical events. If both Debug Server and Syslog Server are specified, Syslog messages are also logged to the Debug Server.
h.     Debug Server - The debug server name and port. This feature specifies the server for logging ATA device debug information. The level of detailed output depends on the debug level parameter setting.
i.     Debug Level - The higher the debug level, the more debug information is generated. Zero (0) means no debug information is generated. To log SIP messages, Debug Level must be set to at least 2. The default is 0.
j.     Primary NTP Server - IP address or name of primary NTP server.
k.     Secondary NTP Server - IP address or name of secondary NTP server.

4.     What are the miscellaneous settings not used with WAG54GP2?

a.     Syslog Server - Specifies the IP address of the syslog server.
b.     Debug Server - Specifies the IP address of the debug server, which logs debug information. The level of detailed output depends on the debug level parameter setting.
c.     Debug Level - Determines the level of debug information that is generated. Select 0, 1, 2, or 3 from the drop-down menu. The higher the debug level, the more debug information is generated. The default is 0, which indicates that no debug information is generated.

5.     What is the default dial plan script for WAG54GP2?

The default dial plan script for each line is as follows: (*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxx|xxxxxxxxxxxx.). The syntax for a dial plan expression is as follows:

 Dial Plan Entry   Functionality
 *xx  Allow arbitrary 2 digit star code
 [3469]11  Allow x11 sequences
 0 Operator
 00  Int'l Operator
  [2-9]xxxxxx US local number
 1xxx[2-9]xxxxxx US 1 + 10-digit long distance number
 xxxxxxxxxxxx. Everything else (Int'l long distance, FWD, ...)

 

6.     What are the FXS Port Polarity Configurations for WAG54GP2?

a.     Idle Polarity - Polarity before a call is connected: Forward or Reverse. The default is Forward.
b.     Caller Conn Polarity - Polarity after an outbound call is connected: Forward or Reverse. The default is Forward.
c.     Callee Conn Polarity - Polarity after an inbound call is connected: Forward or Reverse. The default is Forward.

7.     What are the selective call forward settings?

a.     Cfwd Sel1- 8 Caller - Caller number pattern to trigger Call Forward Selective 1, 2, 3, 4, 5, 6, 7, or 8. The default is blank.
b.     Cfwd Sel1 - 8 Dest - Forward number for Call Forward Selective 1, 2, 3, 4, 5, 6, 7, or 8. Same as Cfwd All Dest. The default is blank.
c.     Block Last Caller - ID of caller blocked via the Block Last Caller service. The default is blank.
d.     Accept Last Caller - ID of caller accepted via the Accept Last Caller service. The default is blank.
e.     Cfwd Last Caller - The Caller number that is actively forwarded to Cfwd Last Dest by using the Call Forward Last activation code. The default is blank.
f.     Cfwd Last Dest - Forward number for the Cfwd Last Caller parameter. Same as Cfwd All Dest. The default is blank.


8.     What is the speed dial setting for WAG54GP2?

Speed Dial 2-9 - Target phone number (or URL) assigned to speed dial 2, 3, 4, 5, 6, 7, 8, or 9. The default is blank.

9.     What is the distinctive ring setting for WAG54GP2?

Caller number patterns are matched from Ring 1 to Ring 8. The first match (not the closest match) will be used for alerting the subscriber.

Ring1 - 9 Caller - Caller number pattern to play Distinctive Ring/CWT 1, 2, 3, 4, 5, 6, 7, 8, or 9. The default is blank.

10.     What are the ring settings for WAG54GP2?

a.     Default Ring - Default ringing pattern, 1 - 8, for all callers. The default is 1.
b.     Default CWT - Default CWT pattern, 1 - 8, for all callers. The default is 2.
c.     Hold Reminder Ring - Ring pattern for reminder of a holding call when the phone is on-hook. The default is None.
d.     Call Back Ring - Ring pattern for call back notification. The default is None.
e.     Cfwd Ring Splash Len - Duration of ring splash when a call is forwarded (0 - 10.0s). The default is 0.
g.     Cblk Ring Splash Len - Duration of ring splash when a call is blocked (0 - 10.0s). The default is 0.
h.     VMWI Ring Splash Len - Duration of ring splash when new messages arrive before the VMWI signal is applied (0 - 10.0s). The default is .5.
i.     VMWI Ring Policy - The parameter controls when a ring splash is played when the VM server sends a SIP NOTIFY message to the ATA device indicating the status of the subscriber's mail box. 3 settings are available: 

i) New VM Available-rings as long as there is 1 or more unread voice mail.
ii) New VM Becomes Available-ring when the number of unread voice mail changes from 0 to non-zero.
iii) New VM Arrives-ring when the number of unread voice mail increases. The default is New VM Available.

j.     Ring On No New VM - If enabled, the ATA device will play a ring splash when the VM server sends SIP NOTIFY message to the ATA device indicating that there are no more unread voice mails. Some equipment requires a short ring to precede the FSK signal to turn off VMWI lamp. The default is no.

 



Was this support article useful?

Additional Support Questions?

Search Again

CONTACT SUPPORT