text.skipToContent text.skipToNavigation

Linksys LAPN600 Business Access Point Wireless Wi-Fi Dual Band 2.4 + 5GHz N600 with PoE Frequently Asked Questions

TABLE OF CONTENTS
 
HARDWARE INFORMATION
 
  1. What is the Linksys LAPN600 Business Access Point Wireless Wi-Fi Dual Band 2.4 + 5GHz N600 with PoE?
  2. What is the default username and password to access the web-based setup page of the Linksys LAPN600?
  3. What is the default IP address of the Linksys LAPN600?
  4. What is the speed of the ethernet port on the Linksys LAPN600?
  5. Does the Linksys LAPN600 come with a Setup Wizard?
  6. Can I use the 2.4 GHz and 5 GHz bands at the same time?
  7. Does the Linksys LAPN600 support Power over Ethernet (PoE)?
  8. How can I reset the Linksys LAPN600 to factory default?
  9. What power adapter does the Linksys LAPN600 use?
  10. Can the antennas be replaced?
  11. Is it possible to wall-mount the Linksys LAPN600?
 
LIGHT INDICATORS
 
  1. What light indicators does the Linksys LAPN600 have?
  2. What should I do if the light indicator is not lit up on the wireless access point when I am using a PoE switch to it?
 
WIRELESS SECURITY
 
  1. What type of wireless security does the Linksys LAPN600 use?
  2. Does it support a RADIUS server?
  3. Does the Linksys LAPN600 support WEP with ASCII format?
  4. How do I enable MAC filtering on the Linksys LAPN600?
  5. How do I associate a VLAN to a Wi-Fi network?
  6. I have Management Access enabled but why is it that wireless clients can still access the web-based setup page?
  7. What does "Bad Format" error message mean when I am in the Wireless > Connection Control page?
 
SPECIAL FEATURES
 
  1. Can the access point act as my DHCP Server?
  2. Can I run an application from a remote computer over the Wi-Fi network?
  3. Can the access point work with a Centrino client?
  4. What are the IEEE 802.11b, 802.11g and 802.11n standards all about?
  5. What IPv6 features are supported?
  6. What is the ISM band?
  7. Would the information be intercepted while transmitting on air?
  8. What is a MAC address?
  9. What is a Rogue AP?
  10. How does the Rogue AP Detection feature work?
  11. What is a workgroup bridge?
  12. How do I avoid interference?
  13. How do I resolve issues with signal loss?
  14. Does the access point function as a firewall?
  15. I have excellent signal strength, but why can't I see my network?
  16. How many Wi-Fi network can the Linksys LAPN600 support?
  17. Can I configure the Linksys LAPN600 by HTTPS?
  18. Does the Linksys LAPN600 support the Netbios Protocol?
  19. How does it work when the channel is configured to "Auto"?
  20. Can the workgroup bridge work at 2.4 GHz and 5 GHz at the same time?
  21. Since the Linksys LAPN600 supports dual images, can the user swap the FWs between two flashes?
  22. How many MAC addresses does the Linksys LAPN600 have?
  23. What version of SNMP does the Linksys LAPN600 support?
  24. Are there operating system and browser limitations in using the Linksys LAPN600?
  25. Why can't I enable HTTP to HTTPS Redirect when I am in the Management Access page?
  26. Can users access the web-based setup page and change any of the configurations?
  27. How do I use the packet capture feature on the Linksys LAPN600?
  28. How do I use the Diagnostic Log?
 
FIRMWARE UPGRADE
 
  1. How do I upgrade the firmware on the Linksys LAPN600?


HARDWARE INFORMATION

1.  What is the Linksys LAPN600 Business Access Point Wireless Wi-Fi Dual Band 2.4 + 5GHz N600 with PoE?

The Linksys LAPN600 Business Access Point Wireless Wi-Fi Dual Band 2.4 + 5GHz N600 with PoE is a 2.4 GHz, IEEE802.11n compliant wireless access point with a Gigabit Ethernet PoE and is backward compatible with widely deployed 802.11/b/g infrastructure.

2.  What is the default username and password to access the web-based setup page of the Linksys LAPN600?

The default username and password is admin.

3.  What is the default IP address of the Linksys LAPN600?

The device acts as a DHCP client by default, and will try to get IP address from a DHCP server.  If there is no DHCP server on your network, device will roll back to default IP address 192.168.1.252.

NOTE:  If the device is already connected to a DHCP server such as a router, you can also determine its IP address by checking the router’s DHCP client table.  To learn how, click
hereAnother way is to ping it through the command prompt using the command “ping LAPXXXXX” where X is the last five digits of the MAC address of your device.

4.  What is the speed of the ethernet port on the Linksys LAPN600?

The speed is 10/100/1000 Mbps.

5.  Does the Linksys LAPN600 come with a Setup Wizard?

The Linksys LAPN600 comes with a built in setup wizard in its web-based setup page called Quick Start and not through a setup CD.

6.  Can I use the 2.4 GHz and 5 GHz bands at the same time?

Yes, the Linksys LAPN600 can support 2.4 GHz and 5 GHz bands at the same time.

7.  Does the Linksys LAPN600 support Power over Ethernet (PoE)?

Yes, the Linksys LAPN600 supports Power over Ethernet (PoE).  The system's maximum power consumption is 17W.  It can be powered ON from an 802.3at compliance source.

8.  How can I reset the Linksys LAPN600 to factory default?

To reset your Linksys LAPN600 to factory default settings, press and hold the Reset button for more than 15 seconds.  Alternatively, you can also reset the LAPN600 by accessing the web-based setup page and going to the Maintenance tab > Factory Default sub-tab.  Click on Yes on the Radio option then click Save.

9.  What power adapter does the Linksys LAPN600 use?

The Linksys LAPN600 adapter uses 12 Volts, 1.5 Amps.

10.  Can the antennas be replaced?

No, the device only uses internal antennas.

11.  Is it possible to wall-mount the Linksys LAPN600?

Yes, the Linksys LAPN600 can be wall-mounted as well as ceiling-mounted.  To learn how, click here.


LIGHT INDICATORS

1.  What light indicators does the Linksys LAPN600 have?

The Linksys LAPN600 has only one light indicator but it shows different colors depending on the status of the device:
  • Green - The light indicator will blink green when the system is booting.  It turns solid when the system is normal and no wireless device is connected.
  • Blue - The light indicator will blink blue when system upgrade is in process, and turns solid when the system is normal with at least one wireless device connected.
  • Red - The light indicator will be solid red when the booting or update process failed and a hard reset is required.
2.  What should I do if the light indicator is not lit up on the wireless access point when I am using a PoE switch to it?

If you are using a PoE switch to provide power to the wireless access point but its light indicator is not lit up, do the following:
  • Make sure that the ethernet cable connecting the wireless access point and the PoE switch is connected properly at both ends.
  • Make sure that the power cord of the PoE switch is plugged into a working power outlet or power strip.
  • Make sure that the PoE switch is functioning normally.
  • Check PoE switch for power limitations.


WIRELESS SECURITY

1.  What type of wireless security does the Linksys LAPN600 use?

The Linksys LAPN600 is compatible with six wireless security types: WEP 64/128 bit, WPA2
-personal, WPA/WPA2-personal, WPA2-Enterprise, and WPA/WPA2-Enterprise, RADIUS.

2.  Does it support a RADIUS server?

Yes.

3.  Does the Linksys LAPN600 support WEP with ASCII format?

No.  The Linksys LAPN600 only supports WEP with HEX format security key.

4.  How do I enable MAC filtering on the Linksys LAPN600?

In the web-based setup page of the Linksys LAPN600, go to Configuration > Connection control.  Select a Wi-Fi network, select Local and enter the MAC address then select Allow or Deny.

5.  How do I associate a VLAN to a Wi-Fi network?

In the web-based setup page, enable VLAN in LAN > Network Setup then go to Wireless > Basic Settings.  Select a Wi-Fi network and enter a VLAN ID then click Save.

NOTE:  When VLAN is enabled, the workgroup bridge feature will be disabled.


6.  I have Management Access enabled but why is it that wireless clients can still access the web-based setup page?

If the client is connected via an ethernet cable to the same network or associated to a different AP in the same network, this is expected.  This feature works if the wireless client is wirelessly associated to the Wi-Fi of the specific AP that has this feature enabled.

7.  What does "Bad Format" error message mean when I am in the Wireless > Connection Control page?

This error occurs when there are no colons in the MAC address field as you enter them.  The correct format needs to be xx:xx:xx:xx:xx:xx.


SPECIAL FEATURES

1.  Can the access point act as my DHCP Server?

No.  The access point is similar to a wireless hub and has no DHCP capabilities.

2.  Can I run an application from a remote computer over the Wi-Fi network?

This depends on whether or not the application is designed to be used over a network.  Consult the application’s documentation to determine if it supports such operation.

3.  Can the access point work with a Centrino client?

Yes.  However, a Centrino client may only support 20 MHz channels so the maximum data rate with this client will be less than 130 Mbps.  

4.  What are the IEEE 802.11b, 802.11g and 802.11n standards all about?

These are IEEE standards for wireless networks.  These standards allow wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with these standards.  The following are the maximum data transfer and operating frequency of these standards:
  • 802.11b - maximum data transfer rate of 11 Mbps and operating frequency of 2.4 GHz
  • 802.11g - maximum data transfer rate of 54 Mbps and operating frequency of 2.4 GHz
  • 802.11n - maximum data transfer rate of 600 Mbps and operating frequency of either 2.4 GHz or 5 GHz
5.  What IPv6 features are supported?

The Linksys LAPN600 supports the following IPv6 functions:
  • Path MTU discovery (RFC1981)
  • Internet Protocol v6 -IPv6 (RFC2460)
  • IPv6 Neighbor Discovery (ND) (RFC2461)
  • IPv6 Stateless Address autoconfiguration (RFC2462)
  • ICMPv6: Internet Control Message Protocol v6 ICMPv6 (RFC2643)
  • IPv6 Address architecture (RFC3513)
  • Default address selection (RFC3484)
  • Transmission of IPv6 Packets over ethernet Networks (RFC 2464)
  • IPv6 Node - (RFC4294)
  • Dual IPv4/IPv6 stack - simultaneous access from IPv4 and IPv6 client at the same time.

6.  What is the ISM band?

The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the Industrial, Scientific and Medical (ISM) band.  Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide.  This presents a truly revolutionary opportunity to place convenient high speed wireless capabilities in the hands of users around the globe.  

7.  Would the information be intercepted while transmitting on air?

WLAN features two-fold protection in security.  On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security feature of scrambling.  On the software side, the WLAN series offers a variety of wireless security methods to enhance security and access control.  Users can set it up depending upon their needs.

8.  What is a MAC address?

The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any ethernet networking device (such as a network adapter) that allows the network to identify it at the hardware level.  For all practical purposes, this number is usually permanent.  Unlike an IP address which can change every time a computer logs on to the network, the MAC address of a device stays the same, making it a valuable identifier for the network.

9.  What is a Rogue AP?
 
A Rogue AP is an access point that has been installed on a secure network without explicit authorization from a system administrator.  Rogue access points pose a security threat because anyone with access to the premises can ignorantly or maliciously install an inexpensive wireless AP device that can potentially allow unauthorized parties to access the network.

10.  How does the Rogue AP Detection feature work?

As soon as this feature is enabled in the Linksys LAPN600 and the user accesses the Rogue AP detection in the web-based setup page, site survey will be done at once and the screen will display the results of Rogue AP detection.

11.  What is a workgroup bridge?

A workgroup bridge feature enables the AP to extend the accessibility of a remote network.  In workgroup bridge mode, the AP acts as a wireless station (STA) on the wireless LAN.  It can bridge traffic between a remote wired network or associated wireless clients and the wireless LAN that is connected using the workgroup bridge mode.

12.  How do I avoid interference?

Using multiple access points on the same channel and in close proximity to one another will generate interference.  When employing multiple access points, make sure to operate each one on a different channel or frequency.

13.  How do I resolve issues with signal loss?

There is no way to know the exact range of your wireless network without testing.  Every obstacle placed between an access point and wireless computer will create signal loss.  Leaded glass, metal, concrete floors, water, and walls will inhibit the signal and reduce range.  Start with your access point and your wireless computer in the same room and move it away in small increments to determine the maximum range in your environment.

You may also try using different channels, as this may eliminate interference affecting only one channel.  You can also go to the access point’s web-based utility, click Wireless > Advanced Settings and make sure the output power is set to 100 percent.


14.  Does the access point function as a firewall?

No.  The access point is only a bridge from wired ethernet to wireless clients.  

15.  I have excellent signal strength, but why can’t I see my network?

Wireless security, such as WEP or WPA, is probably enabled on the access point, but not on your wireless adapter or vice versa.  Verify that the same wireless security settings are being used on all devices in your wireless network.  

16.  How many Wi-Fi network can the Linksys LAPN600 support?

The Linksys LAPN600 supports eight Wi-Fi network on every radio using eight different MAC addresses.

17.  Can I configure the Linksys LAPN600 by HTTPS?

Yes.

18.  Does the Linksys LAPN600 support the Netbios Protocol?

Yes.

19.  How does it work when the channel is configured to "Auto"?

The Linksys LAPN600 will check the channel with the lowest amount of wireless interference when device reboot or user changes the parameters of wireless radio to trigger the radio to restart.  The wireless client will connect to this channel with the lowest amount of wireless interference.

20.  Can the workgroup bridge work at 2.4 GHz and 5 GHz at the same time?

No.  The workgroup bridge only works with one radio at the same time.

21.  Since the Linksys LAPN600 supports dual images, can the user swap the FWs between two flashes?

No.

22.  How many MAC addresses does the Linksys LAPN600 have?

The Linksys LAPN600 has three legal global MAC addresses.  One is LAN MAC address and the other two are Wi-Fi radio interface MAC addresses for 2.4 GHz and 5 GHz.  The multiple Wi-Fi network and workgroup bridge interface MAC addresses are temporary MAC addresses and they are calculated based on Wi-Fi radio interface MAC address.

23.  What version of SNMP does the Linksys LAPN600 support?

Linksys LAPN600 supports versions 1, 2 and 3.

24.  Are there operating system and browser limitations in using the Linksys LAPN600?

There are no operating system limitations.  Just make sure the browser supports Javascript such as the following:
  • Internet Explorer® 7.0 or later
  • Chrome™ 8 or later
  • Firefox® 3.5 or later
  • Safari® 5 or later

25.  Why can't I enable HTTP to HTTPS Redirect when I am in the Management Access page?

You should disable HTTP first before you can enable HTTP to HTTPS Redirect.

26.  Can users access the web-based setup page and change any of the configurations?

Yes, users can access the web-based setup page but they have read only permissions.  Only admin accounts will have read/write permissions.

27.  How do I use the packet capture feature on the Linksys LAPN600?  

This feature will only capture the packets.  Upon clicking start, you will be prompted to save the file, however, you will need third party software to open and analyze the packet such as Wireshark.

28.  How do I use the Diagnostic Log?

This is only for engineering use.  Should a technician request a log, you can only download and provide the log to the technician.


FIRMWARE UPGRADE

1.  How do I upgrade the firmware on the Linksys LAPN600?

 
Step 1:
Access the access point’s web-based setup page.

Step 2:
Click on Maintenance > Firmware Upgrade tab, click the Choose File button and select the new firmware file.

Step3:
Click the Upgrade button.

 
NOTE:  Do not power OFF or press the Reset button while upgrading the firmware of the access point.  The Linksys LAPN600 will reboot automatically after the firmware upgrade is completed.

Was this support article useful?

Additional Support Questions?

Search Again

CONTACT SUPPORT