PLW400 Frequently Asked Questions
TABLE OF CONTENTS
PORTS AND BUTTONS
1. How do I connect my PLW400?
2. What should I do if none of the LEDs turned on after I installed the Powerline adapter?
3. What should I do if the Ethernet LED does not turn ON after I connected a wired device to the powerline adapter?
4. What should I do if I cannot connect to other computers on my local network or to the Internet?
5. What does it mean if the LEDs are flashing on my PLW400?
FIRMWARE UPGRADE METHOD
1. What is the transfer rate of the PLW400?
2. Does the PLW400 have a web-based setup page?
3. Does the PLW400 support TCP/IP for standard routers?
4. What is the internal power supply used by the PLW400?
The PLW400 is a Powerline 1-Port Fast Ethernet Network Adapter and Access point in one device. This adapter provides easy setup and lets you connect wireless networking devices to your powerline network.
The warranty period is dependent on the country of purchase. For more information about your device's warranty, click here.
- A computer or other device with Ethernet adapter
- Available AC power jack on the same circuit
- Other Powerline AV enabled Device
NOTE: Make sure first that the PLW400 is configured on the same power jack as the rest of the Powerline equipments.
After configuring the PLW400 on one power jack, move it to another power jack you would like to use. If the Powerline LED lights up, then it is on the same circuit and should work fine. If the LED does not light, try other nearby power jacks.
On the first adapter, press and hold the HomePlug Simple Connect button for at least one (1) second until the Powerline LED begins flashing slowly. This means that the adapter creates a new network key for the Powerline network.
On each of the other adapters, press and hold the HomePlug Simple Connect button for at least one (1) second, until the Powerline LED begins flashing slowly. When the LED stops flashing, it is an indication that the new network key has been shared with that adapter.
The PLW400 has Powerline, Ethernet, Wireless, Wi-Fi Protected Setup™ (WPS) and Power LEDs.
- Powerline LED - turns ON when the adapter is connected to the Powerline network. The LED flashes to indicate network activity.
- Ethernet LED - turns on when a wired network device is turned on and connected to the adapter’s Ethernet (network) port. The LED flashes to indicate network activity.
- Wireless LED - turns on when a wireless network device is connected to your PLW400.
- Wi-Fi Protected Setup™ LED - flashes while a wireless network device is connecting with your PLW400 using Wi-Fi Protected Setup™.
- Power LED - turns on when the adapter is connected to a powered electrical outlet.
PORTS AND BUTTONS
- Ethernet port - This Ethernet port connects a computer or another networking device to the PLW400.
- Reset button – Restores your powerline adapter to factory defaults. To do this, press and hold the Reset button for at least 10 seconds using a pin or a pointed object.
- HomePlug Simple Connect button - Configures advanced security (the network password) for your powerline network.
- Wi-fi Protected Setup™ button - connect with other wireless network devices that have a Wi-Fi Protected Setup™ button.
IMPORTANT: Before proceeding, make sure that the power switch on the right side is set to I (ON). If your home network already has security set up (recommended):
Connect the PLW400 to a power outlet near your main wireless router.
On the PLW400, press and hold the Wi-Fi Protected Setup™ button at least one (1)second, until the WPS LED flashes.
On your wireless router, press the Wi-Fi Protected Setup™ button for two (2) minutes. The PLW400 retrieves the security settings from the router and connects to your wireless network.
Move your PLW400 to a power outlet near the wireless network device(s) you want to connect. Typically, this area is not covered well by your home’s wireless network router. The Powerline LED flashes, and then stays solid when the connection to the rest of the Powerline network is finished. Your home’s wireless network is now available in the area surrounding the PLW400.
Connect the wireless network device to the wireless network in the usual manner. For instructions, see your wireless network device’s user documentation. The PLW400’s Wireless LED flashes, and then stays solid when a wireless network device successfully connects.
Disconnect the adapter from the power outlet.
Disconnect the Ethernet cable from the adapter.
Wait five (5) seconds.
Re-connect the Ethernet cable to the adapter.
Re-connect the adapter to the power outlet.
NOTE: If this solution does not work, make sure that the electrical outlet is working properly. Plug a different device into the power outlet, and try to switch it on.
When the Ethernet port detects a local network connection, the Ethernet LED should turn ON. If it does not, do the following:
- Make sure that the Ethernet cable is securely connected to the adapter.
- Make sure that the Ethernet cable is securely connected to the computer or other network device.
- Make sure that the Ethernet adapter on your computer is working properly.
If you did not set up advanced security for the Powerline network, follow these instructions:
Locate the Powerline adapter connected to the computer that cannot connect.
On the right side of the adapter, use a pointed object to press and hold the Standby/Reset button for at least ten seconds. This resets the adapter to its factory default settings.
If you have set up advanced security for the Powerline network, check the following:
1. Make sure all adapters on the Powerline network have been configured with the same network password. The network password must be identical in order for them to communicate with each other.
2. If you are adding a new adapter to a pre-existing Powerline network with a unique network password.
Refer to the following LED behavior to help diagnose the problem:
- Off- Not connected to Powerline network
- Flashing fast- Send/Receive data
- Flashing slow- Pairing
- Solid- Connected to Powerline network
- Off- Not connected to Ethernet network
- Flashing- Send/Receive data
- Solid- Connected to Ethernet network
- Off- Device power off
- Solid- Device power on and ready
- Flashing fast momentarily- Factory default, Device wakeup from standby mode
- Flashing fast indefinitely- Pairing error/system error
- Flashing slow- Device in standby mode
- Off- The Wireless LED lights off when the wireless feature is disabled
- Solid- The Wireless LED lights up when the wireless feature is enabled
- Flashing- Send/Receive data
WI-FI PROTECTED SETUP™:
- Off- The WPS LED lights off when the WPS feature is disabled
- Solid- this LED flashes while a wireless network device is connecting with your PLW400 using Wi-Fi Protected Setup™
- Flashing- The LED flashes when a WPS session is active
FIRMWARE UPGRADE METHOD
There are two (2) ways to upgrade the firmware of your powerline adapter:
- Using the Linksys Powerline AV Utility - Launch the utility and under Network Status tab, select PLW400. Go to the Administration tab then click on the Upgrade button under Firmware Upgrade.
- Using the web-based set-up page - Access the web-based setup page and go to Administration tab > Firmware Upgrade sub-tab. Click on the Browse button and look for the firmware file you have downloaded then click the Start Upgrade button.
The transfer rate is 200 mbps at physical layer, and it supports the 802.11b, 802.11g or 802.11n standard wireless clients.
100-240V AC/ 50-60 Hz.