text.skipToContent text.skipToNavigation

Getting to know the Linksys 26-port Smart Gigabit Switch, LGS326

Linksys 26-port Smart Gigabit Switch, LGS326 offers a quick and easy solution to extend your office network and connect devices.  LGS326 has 24 Gigabit ports (RJ-45) plus two (2) Gigabit Combo ports.
 
Fast and convenient access to your file
 
The LGS326 switch offers Gigabit speeds to minimize file transfer duration and greatly enhance your ability to stream high-bandwidth files to connected devices without interference.
 
Easy to configure and operate
 
With its web-based setup page, this Smart Switch also provides easy installation and management to users. 
 
Front panel
 

 

 
Combo ports - It is a single-logical port that has two (2) physical connections, the RJ45 connector (copper) and SFP connector (fiber).
  • Only ONE of the two (2) physical connections may be used at a time.  The system will automatically detect the media that is in use on a combo port. 
  • If both RJ45 and SFP are present (link up in both connections), the SFP will be active, and the RJ45 connection will be disabled and ignored.  The RJ45 connection will be in standby and automatically enabled if the SFP link goes down.
  • The SFP and RJ-45 interfaces share a common link/activity and speed LEDs.
  • Some port controls are affected by the actual physical connection used.
  • The SFP interface supports both Gigabit and 100 Mbps speeds.
  • SFPs officially tested:
–      PTO-S1-4103K- IE
–      PTO-M3-4D33K- IE   
–      PT4-S1-4103K- I
–      PT4-M3-4D53K- I
 
 RESET button - The reset button is located on the device’s front panel next to the system LEDs.
 
Reset Button Behavior:
  • Pressing for less than 10 seconds will cause system to reboot after releasing the button.
  • Pressing the button for more than 10 seconds will cause the system to reboot to factory default settings. 
 SYSTEM LED - Indicates the device’s status and activities.
  • OFF - System is powered OFF.
  • Solid Blue - System is ON and operative.
  • Blinking Blue:
? Booting/System Self-Test
? Device is using the factory default IP address of 192.168.1. 251
  • Blinking Yellow - Failure detect (e.g. Fan)  
NOTE:  To know more about the LEDs on the Smart Gigabit Switches, click here.
 
Back panel
 
 
 
 
Features
  • Port Mirroring - up to four (4) sources to one target
  • MAC Address Aging - Range 10-630 sec, default 300 sec
  • Spanning Tree - STP/RSTP
  • SNMP - OID placing/MIB root
  • System software and Configuration Management
  • Quality of Service (QoS)/Class of Service and Rate Limiting
  • System IP address Management
  • Security - RADIUS
  • Switch Management 
Package Contents
  • Linksys SMB Smart Switch
  • Quick Start Guide
  • Power cord and adapter
  • CD with documentation
  • Rack mount kit or wall mount kit 
Device management
 
The switch can be managed by:
  • Web-based setup page (HTTP, HTTPS)
  • Telnet (Menu CLI)
  • SNMP
Supported browsers
  • Firefox version 16 and latest
  • Internet Explorer 9-10 
Supported host operating system
  • Windows XP
  • Windows 7 (32 & 64 bit) 
Memory
 
DDR2 SDRAM: 64 MB x 16
SPI Flash: 16 MB

Hat Ihnen dieser Support-Artikel geholfen?

Haben Sie noch Fragen an den Support?

Erneut suchen

SUPPORT KONTAKTIEREN