text.skipToContent text.skipToNavigation

Getting to know the Linksys LAPAC2600 Business Pro Series Wireless-AC Dual-Band MU-MIMO Access Point

The Linksys LAPAC2600 Business Pro Series Wireless-AC Dual-Band MU-MIMO Access Point is an 802.11ac dual-band, 4x4 MU-MIMO access point.  It provides continuous and high-speed access between wireless and Ethernet devices.  The access point enables wireless local area network (WLAN) deployment while providing state-of-the-art wireless networking features.
 
User-added image

Product Features
 
  • Compatible with 802.11 a/b/g/n
  • Built-in Setup Wizard
  • Supports 802.11r/k
  • Beamforming
  • PHY data rate up to 800 Mbps (2.4 GHz) and up to 1.8 Gbps (5 GHz)
  • Supports up to eight (8) SSIDs for each band (16 total)
  • Client Isolation
  • Workgroup bridge mode
  • WDS support
  • Captive Portal support
  • Advanced security and preventions
  • IPv6 support
  • Rogue AP Detection
  • Cluster feature
  • 2 x Gigabit ports
  • PoE (Port 1)
  • IPv4 / IPv6 ACL
LED Behavior
 
LED ColorActivityStatus
GreenBlinkingSystem is booting.
SolidSystem is normal; no wireless device connected
BlueBlinkingSoftware upgrade in process.
SolidSystem is normal; at least one (1) wireless device connected.
RedSolidBooting process or upgrade failed; hard reset or service required.

Bottom Panel

User-added image
Power Port
– Connect the AC power adapter to this port.  The power adapter uses 12 V.
 
NOTE:  Use ONLY the adapter that came with your access point.

User-added image
Ethernet Port 1 (Power over Ethernet (PoE))
– Use an RJ45 (Cat5e or better) cable to connect the Linksys LAPAC2600 to other networking devices like routers, switches or computers.   This port supports PoE+ (IEEE 802.3at).  You may use the port to power the access point by using a PoE+ switch or injector.

NOTE:  PoE has higher precedence over AC.  When both PoE and AC power adapter are connected to Linksys LAPAC2600, the device will be powered by PoE.

User-added image
Ethernet Port 2
– This is a non-PoE Ethernet port.  It can be used instead of Ethernet Port 1 but requires AC power adapter to power the access point.
 
NOTE:  Ethernet Port 1 and Port 2 can be used together in Link Aggregation mode when supported by the connected devices.  In this configuration, it is highly recommended that AC power and PoE be used in tandem to support power failure and/or link failure.

User-added image
Reset Button
– Press and hold the button for less than 15 seconds to powercycle the device.  Press and hold for 15 seconds to reset the device to factory default settings.

User-added image
Lock Slot
– Slot for security lock.
 
Product Requirements
  • No operating system limitations
  • Browser must support JavaScript
  • Internet Explorer® (IE) 8 or later
  • Chrome™ 8 or later
  • Firefox® 35 or later
  • Safari® 5 or later


Related Video:

Getting to know the Linksys LAPAC2600 (VIDEO)
Setting up the Linksys LAPAC2600 (VIDEO)
Getting to know the LAPAC1750PRO BUSINESS AC1750 PRO DUAL-BAND ACCESS POINT (VIDEO)
Configuring the Captive Portal feature of the Linksys LAPAC2600 (VIDEO)
How to copy or save configurations within your Linksys LAPAC2600 Wireless Access Point (VIDEO)

Was this support article useful?

Additional Support Questions?

Search Again

CONTACT SUPPORT