Overview of the External Storage feature of the Linksys MX4000 Series WiFi 6 System

The External Storage feature of the Linksys MX4000 Series WiFi 6 System allows you to connect an external storage device to the USB port on the node and share the entire drive.

The Linksys MX4000 Series feature one USB 3.0 port for the storage drive.  If you have more than one of this router, you can connect a USB hard drive into each node.

NOTE:  Virtual printing is not supported.


sf317564-001_en_v3.png

Click the links below for details on the External Storage feature:

Supported file formats
Linksys app view
LinksysSmartWiFi.com
Network File Sharing (SMB)

 

Supported file formats

This router supports the following USB file formats:


Windows®:
NTFS and FAT32

Mac®:
FAT32 and HFS+ (journaled, non-journaled)

 


Linksys app view

To access the dashboard page using an Android™ device, follow the instructions here.  For iOS, click here.  Then, tap on the Menu icon and go to External Storage.


NOTE:  Images may vary depending on the operating system of your mobile device.

sf317564-002_en_v3.png

The following settings will be displayed: 

sf317564-003_en_v3.png

 
  • The node’s name (e.g., Family Room and Living Room).  In the example above, Parent node is used.
  • The Refresh sf317564-004_en_v3.png icon (located in the External Storage header)
  • The Eject icon – Tap on sf317564-005_en_v3.png to safely remove the drive.  This will also prevent file corruption.
  • The following hard drive details will also be displayed:
  • The name of the hard drive/partition 
  • The storage capacity and total storage used for every hard drive or partition
  • The IP address for SMB access computers within the networkcan access the connected storage device using this IP address
  • Authentication - To enable it, tap Authentication and toggle the sliding switch to the right.  Enter your preferred username and password then tap on Save.
NOTE:  When Authentication is turned ON, access to the storage device will be available only to those who have the username and password that you have set.  Authentication is disabled by default.


sf317564-006_en_v3.png 

Authentication requirements:

The username should have a minimum of four and a maximum of 12 alphanumeric characters while the password should have a minimum of four and maximum of 50 alphanumeric characters.  Both can include valid characters such as an underscore ( _ ) or a dash ( - ).

 

LinksysSmartWiFi.com

To access the dashboard page, follow the instructions here.  Then, go to External Storage under Smart Wi-Fi Tools.


sf317564-007_en_v3.png

The following settings will be displayed:

sf317564-008_en_v3.png 
 
  • The node’s name.  In the example above, Parent node is used.
  • The Refresh sf317564-009_en_v3.png button
  • The Eject icon – Click on this sf317564-010_en_v3.png icon to safely remove the drive.  This will also prevent file corruption.
  • The following hard drive details will also be displayed:
  • The name of the hard drive/partition
  • The storage capacity and total storage used for every hard drive or partition
  • The IP address for SMB access - computers within the network can access the connected storage device using this IP address
  • Authentication - To enable it, simply toggle the sliding switch to the ON position.  Enter your preferred username and password and click on Apply to save your changes then click Ok.
 
NOTE:  When Authentication is turned ON, access to the storage device will be available only to those who have the username and password that you have set.  Authentication is disabled by default.
 

sf317564-011_en_v3.png

Authentication requirements:

The username should have a minimum of four and a maximum of 12 alphanumeric characters while the password should have a minimum of four and maximum of 50 alphanumeric characters.  Both can include valid characters such as an underscore ( _ ) or a dash ( - ).

 

Network File Sharing (SMB)

This section will guide you on how to access the storage device connected to the node.  The Linksys MX4000 Series supports SMB v2.0.  If you have a router that only supports SMB v1.0, click here for instructions on how to enable SMB v1.0.

To access the drive, look for its IP address either in the Linksys app or the LinksysSmartWiFi.com of your Linksys MX4000 Series and do the following:

For Windows computers:

Enter “\\” followed by the IP address of the storage drive you want to access into the Windows Explorer field, then hit [ENTER].

In the example below, “\\192.168.1.1” is used.


sf317564-012_en_v3.png

For Mac computers:

Navigate to Go > Connect to Server and enter “smb://” followed by the IP address of the storage drive you want to access, and then click Connect.  

In the example below, “smb://192.168.1.1” is used.


sf317564-013_en_v3.png
 
 

Was this support article useful?

Additional Support Questions?
Search Again