text.skipToContent text.skipToNavigation

Setting up your Linksys range extender in Access Point mode

The newer Linksys range extenders can be configured to work in Access Point mode.  Access Point mode lets your range extender expand your WiFi by connecting to your router or switch though a cable, which enables it to have minimal loss of performance or dropping connection.  For better WiFi speeds, choose Access Point mode.  This article will show you how you can set up your range extender as an Access Point.

These are the Linksys range extenders you can set up in Access Point mode:
  • Linksys RE7350 Max-Stream™ WiFi 6 Range Extender
  • Linksys RE7000 Max-Stream™ AC1900+ WiFi Extender
  • Linksys RE6800 AC1750 WiFi Extender
  • Linksys RE6700 AC1200 AMPLIFY Dual-Band WiFi Extender
  • Linksys RE6500 AC1200 Dual-Band WiFi Extender
  • Linksys RE6500HG AC1200 Dual-Band WiFi Extender
  • Linksys RE6400 AC1200 BOOST EX WiFi Extender
  • Linksys RE6300 AC750 BOOST WiFi Extender
Before you start the setup process, ensure the following:
 
  1. An active WiFi connection.
  2. Your WiFi name and WiFi password / security key.  For instructions on how to check these WiFi settings on your Linksys router, click here.
  3. An ethernet cable long enough to connect your router to your range extender.
Once you're ready, follow the steps below.

NOTE:  In the example below, a Linksys
RE7350 was used.

Step 1:
Plug your range extender into a power outlet.  Wait until the light starts blinking orange.
 
Step 2:
Connect an ethernet cable from the router to your range extender.  Depending on your range extender's model, you might need to wait for the light to turn green before proceeding to the next step.
 
Step 3:
Connect a wireless computer or a mobile device to the range extender's default SSID, which is Linksys Extender Setup – xxx.
 
NOTE:  The xxx represents the last three characters of your range extender's MAC address, which can be found at the back label of the device.
 
Step 4:
Open a web browser, then enter "https://extender.linksys.com" in the Address bar.  If it doesn't load, you will need to look up your range extender's IP address in your router’s DHCP client table.  To know how to do this on Linksys WiFi Routers, click hereFor Linksys Smart WiFi Routers, click here.
 
Step 5:
Click User-added image.
 
User-added image

Step 6:
Click Next under the As a wired range extender (Access point) option.

User-added image
 
NOTE:  If you haven’t connected an ethernet cable from your range extender to your router or switch, it will prompt you to connect the cable and try again.  Ensure that it's connected before proceeding to the next step.
 
Step 7:
Create unique WiFi names that the range extender will be broadcasting, you can either create two different WiFi names or use the same one for both the 2.4 GHz and 5 GHz radio bands.  Create a WiFi password as well, then click Next.

QUICK TIP:  The extended network is the WiFi network that your range extender will be broadcasting.

 
User-added image

 
Step 8:
Create an admin password for your range extender, then click Save.  You may also add a password hint.
 
User-added image

Step 9:
You might be prompted to register your Linksys product to receive updates and other information to improve your experience.  Enter your Email Address then click Next, or click Skip.

 
Your range extender is now set up in Access Point mode.

User-added image

Once your range extender is in Access Point mode, the top right header will read Dual Band Wireless Access Point.

Was this support article useful?

Additional Support Questions?

Search Again

CONTACT SUPPORT