Product comparison chart for the Linksys access points and range extenders

This comparison chart will help you differentiate the Linksys WAPT1200AC, WAP1200AC, WAP750AC, RE7000, and RE6300.
 
FeaturesRE6300RE7000WAP750ACWAP1200ACWAPT1200AC
Simultaneous Dual-BandYesYesYesYesYes
Wireless Technology802.11 a/b/g/n/ac802.11 a/b/g/n/ac802.11 a/b/g/n/ac802.11 a/b/g/n/ac802.11 a/b/g/n/ac
AntennaTwo External (non-detachable)Two 5 GHz Internal and
Two dual-band Internal
antennas
Two External (non-detachable)Two External (non-detachable)Two External (non-detachable)
Data RateUp to 300 Mbps (2.4 GHz)Up to 300 Mbps (2.4 GHz) Up to 300 Mbps (2.4 GHz)Up to 300 Mbps (2.4 GHz)Up to 300 Mbps (2.4 GHz)
Up to 433 Mbps (5 GHz)Up to 1733 Mbps (5 GHz)Up to 433 Mbps (5 GHz)Up to 867 Mbps (5 GHz) Up to 866 Mbps (5 GHz)
Antenna Gain3.9 dBi (2.4 GHz)3.48 dBi (2.4 GHz)3.9 dBi (2.4 GHz)3.9 dBi (2.4 GHz)2.5 dBi (2.4 GHz)
5.9 dBi (5 GHz)3.3 dBi (5 GHz)5.9 dBi (5 GHz)5.9 dBi (5 GHz) 3.5 dBi (5 GHz)
Access Point modeYesYesYesYesYes
Support 802.11r*NoYes
 
NOTE: The 802.11r is supported only on Linksys RE7000 v1 and not on Linksys RE7000 v2.
NoNoNo
 Wi-Fi Protected Setup™ (WPS)YesYesYesYesYes
MountingWall PlugWall PlugWall PlugWall Plug Wall Plug
AC PassthroughNoNoNoNoYes
Spot Finder TechnologyYesYesYesYesYes
Wireless SecurityWEP, WPAâ„¢, WPA2â„¢, and WPA2/WPA Mixed ModeWEP (Range Extender
mode only), WPA, WPA2, and WPA2/WPA Mixed Mode
WEP, WPA, WPA2, and WPA2/WPA Mixed ModeWEP, WPA, WPA2, and WPA2/WPA Mixed ModeWEP, WPA, WPA2, and WPA2/WPA Mixed Mode
Cross Band TechnologyYes (with manual settings)YesYes (with manual settings)YesYes
Temporary DHCP Server for SetupYesYesYesYesYes
Default IP address (temporary)192.168.1.1192.168.1.1192.168.1.1192.168.1.1 192.168.1.1
Ethernet Port1 x 10/10/10001 x 10/10/10001 x 10/10/10001 x 10/10/10001 x 10/10/1000
Maximum wireless clientsUp to 32Up to 32Up to 32Up to 32 Up to 32
Audio PortNoNoNoNoYes

*You can enable this feature if there are two or more Linksys RE7000s in the network and one is set up as an Access Point and the other as a Range Extender. To know more about this feature, click here. 

Was this support article useful?

Additional Support Questions?
Search Again