Setting up the Linksys E9450-SG for Singtel as a parent node using the Setup Wizard

To make sure your Singtel Optical Network setup operates, it is essential to use the Setup Wizard in configuring your Linksys E9450-SG for Singtel Dual-Band Easy Mesh WiFi 6 Router.

NOTE:  There is no option to bypass the setup wizard, you must complete the setup wizard before making any changes in the web interface.

Before you begin, take note of the following:
 
  • You must use the setup wizard to set up your router, otherwise, the router will not work. 
  • You can either use a wired computer or a WiFi device (e.g., a laptop, tablet, or smartphone) to set up the router.
  • To set up the Linksys E9450-SG for Singtel using a WiFi device, you first need to remember the default WiFi name and password of the router.  These are located on the router’s product label.  The default WiFi names of the router are Linksysxxxx (where xxxx represents the last five digits of the router’s serial number).
  • The Linksys E9450-SG for Singtel that is connected to your ONR/ONT equipment will become your parent node.  If you will be extending your WiFi network with additional E9450 models, these are called child nodes.
  • Determine if you have Singtel Optical Network Terminal (ONT) or Singtel Optical Network Router (ONR) and connect your hardware based on the following scenario:
 
 

For Singtel Optical Network Terminal (ONT)

NOTE:  The Singtel box will show Optical Network Terminal (ONT).
 
 

Connect the Linksys E9450-SG for Singtel to your ONT using an ethernet cable to the LAN port.
 
 

 

For Singtel Optical Network Router (ONR)

NOTE:  The Singtel box will show Optical Network Router (ONR).  Some ONR equipment may be on Bridge mode.  For advance users, to determine if your ONR is on Bridge mode, (when your computer is connected to the ONR without Bridge mode) you will get a public IP address range.  If ONR is not in Bridge mode, your computer will get a private IP address.
 
 

Connect one end of the ethernet cable into the yellow-labeled internet (WAN) port of the Linksys E9450-SG for Singtel and the other end to the ethernet (LAN) port of the ONR. 
 
 

This article will show you how to set up and configure your router as a parent node.
 
Step 1: 
Power ON your router and wait for its WiFi and power indicator lights to turn solid blue.

Step 2: 
Using an ethernet cable, connect a computer into one of the ethernet (LAN) ports of your Linksys E9450-SG for Singtel.

NOTE:  If you are using WiFi device to set up the router, connect it to the default WiFi name of the router and log in using the password from the Linksys E9450-SG for Singtel product label.

Step 3:
Open a browser and type in https://linksysxxxxx for Windows or https://linksysxxxx.local for MAC OS (the xxxxx refers to the default WiFi name of the router located on the product label).  You can also use https://192.168.79.1, which is the default IP address of the router.  If your router is using a different IP address, use that one instead.

NOTE:  Depending on which browser you are using, you may come across an error such as the one shown below.  To learn more, click here.
 
 

Step 4:
Enter admin as the username enter the default WiFi Password located on the bottom of the router, then click Apply.
 
 

Step 5:
Click Next.
 
 

Step 6:
Create a new router password that meets all the needed requirements.  Click Next once done.
 
 

Step 7:
Create a Wi-Fi Name and Wi-Fi Password.  Click Next once done.
 
 

Step 8:
If you haven’t done so, connect your router from the Internet port to your Singtel device, then Click Next.
 
 

Wait until the settings are saved.
 
 

Step 9:
Connect your computer to the new WiFi, then click Next.  If your computer is connected wired to the Linksys E9450-SG for Singtel, click Next right away.
 


 

Step 10:
Click I'm Done.
 
 

Your Linksys E9450-SG for Singtel has now been successfully configured.

NOTE:  If you received a message that you are not online, you can log in to the router’s web interface with the new password you created during the setup wizard for additional configuration

Was this support article useful?

Additional Support Questions?
Search Again